1000W Rear Wheel E-Bike Motor Wheel only - watertight plug

*Please be aware that this item may take up to 6-7 weeks to reach you 

High Performance Electric Bicycle Motor:

This High-Performance Rear Electric Bike Motor is suitable for bikes with a 135 mm rear drop-out width (not suitable for thru-axle bikes) and compatible for bikes with disc brake set-ups only (not suited for v-brakes). The motor delivers high-power and allows you to maintain your speed up hills and into the wind. This motor is intented for off-road use only. Please check your local laws and regulations to make sure that this wheel suits you before purchasing

A controller, tyre, throttle, display, PAS (pedal assist sensor), battery and battery charger not included. Use a 48V or 52V battery for optimal performance.

PACKAGE INCLUDES

• 1 x Brushless Direct Drive (gearless) Rear 26” Wheel Hub Motor
• 1 x User Manual

KEY FEATURES

• 36V 48V 52V 1000W powerful Brushless and Gearless (Direct Drive) Hub Motor with watertight wiring connector
• 500 rpm at 48V

SPECIFICATIONS

• Wheel Type: Rear Wheel
• Drop out: 135mm
• Wheel size: 26"
• Rim: Alloy double wall extra strong
• Gears: Freewheel / screw-on (not suitable for Cassette)
• Motor: Brushless DC direct drive
• Torque: 45 Nm
• Power: 1000W (private use) or 250W
• Speed: 55 km/hr with 48V (private use) or 25 km/hr
• Spokes: Steel 12Gx2.6mm
• Mass: 6 kg
• Wheel Axle: 210mm x 10mm DIA.
• Load capacity: 150 kg (inclusive of the completed bike and rider)

WARRANTY

• General Wear and Tear is not covered by warranty.
• Damages occurring due to incorrect fitment are not covered by warranty. Please contact us in case of being unsure of the correct installation or operation beforehand.
• Please take care to properly fit and protect the wiring coming out from the motor axle as this can be damaged if not correctly aligned with your disc rotor.
• Please take care to seat the motor axle fully into the bikes' dropouts during installation (or after puncture repairs) and tighten the 21 mm axle nuts on either side of the motor firmly. Damage caused by incorrect installation is not covered by warranty.
• If using the bike in full power mode, it is highly recommended to fit a torque arm (purchased separately) to both sides of the bike (two in total). The torque arms should be suitably orientated, and tightened, to prevent the axle from free spinning inside the dropouts. Not doing so can result in the motor axle spinning loosely within the dropouts during operation (due to high torque) and cause damage to the wiring directly at/near the motor. This type of damage is not covered by warranty.
• To fit the motor correctly you may require the 5mm steel spacer behind the disc rotor (do not use the compressible plastic one supplied as this is for transportation only) and longer disc rotor bolts. If you are unsure at any stage, please kindly contact us and we will help.
• The kit is not waterproof and therefore should not be immersed in water. Water damage is not covered by warranty.
• Although this kit is renowned for being well designed and long-lasting, damages occurring from incorrect use of the kit is not covered by warranty. The motor is not suitable for doing jumps, wheelies, burnouts, impacts with kerbs, exceeding the recommended weight limit or downhill riding. The kit is most suited to riding on well paved surfaces and enjoying light gravel tracks.

NOTE

Torque arms/plates are not included. Please contact us should you require any more information on installation procedures.

Please ensure the correct installation of this wheel using torque arms fitted in the right orientation and tightening the wheel to your frame snug tight. If unsure of the correct installation proceedure please contact us before proceeding. Incorrect installation and damages occuring due to wrong fitment, lack of torque arms or motor misuse are not covered by warranty.