2000W 26” 27.5" 29" MTX Rear Wheel E-Bike Motor Wheel only

*Please note that the 26" variant may take up to 6–7 weeks to arrive due to current delays in procurement.

MTX HIGH PERFORMANCE ELECTRIC BICYCLE MOTOR

This DIY High-Performance Rear Electric Bike Motor is suitable for bikes with a 135 mm rear drop-out width (not suitable for thru-axle bikes) and compatible for bikes with disc brake (not suitable for v-brake set-ups). The motor delivers high-power and allows you to maintain your speed up hills and into the wind.

Our 2000W motor, compared to the 1000W motor, has a wider stator and larger magnets, and therefore produces more torque for increased acceleration and higher speed up hills. This motor is intented for off-road use only. Please check your local laws and regulations to make sure that this wheel suits you before purchasing

A controller, tyre, throttle, display, PAS (pedal assist sensor), battery and battery charger not included. Use a 48V (or 72V battery for optimal performance).

PACKAGE INCLUDES

• 1 x Brushless Direct Drive (gearless) 26” / 27.5" / 29" Rear Wheel Hub Motor 2000W Wheel only

KEY FEATURES

• 36V 48V 52V 60V 72V 2000W powerful Brushless and Gearless (Direct Drive)
• 490 rpm at 48V

SPECIFICATIONS

• Wheel Type: Rear Wheel
• Drop out: 135mm
• Wheel size: 26", 27.5", 29"
• Rim: MTX Alloy double wall
• Gears: Freewheel / screw-on (not suitable for Cassette) - not included
• Motor: Brushless DC direct drive
• Torque: 55 Nm
• Power: 2000W (private use) or 250W
• Speed: 55 km/hr with 48V (private use) or 25 km/hr
• Spokes: Steel 12Gx2.6mm
• Mass: 8 kg
• Wheel Axle: 210mm x 10mm DIA.
• Load capacity: 150 kg (inclusive of the completed bike and rider)
• MT60 phase wire connectors (or select Lug Ring/Loop connector)

WARRANTY

• General Wear and Tear is not covered by warranty.
• Damages occurring due to incorrect fitment are not covered by warranty. Please contact us in case of being unsure of the correct installation or operation beforehand.
• Please take care to properly fit and protect the wiring coming out from the motor axle as this can be damaged if not correctly aligned with your disc rotor.
• Please take care to seat the motor axle fully into the bikes' dropouts during installation (or after puncture repairs) and tighten the 21 mm axle nuts on either side of the motor firmly. Damage caused by incorrect installation is not covered by warranty.
• If using the bike in full power mode, it is highly recommended to fit a torque arm (purchased separately) to both sides of the bike (two in total). The torque arms should be suitably orientated, and tightened, to prevent the axle from free spinning inside the dropouts. Not doing so can result in the motor axle spinning loosely within the dropouts during operation (due to high torque) and cause damage to the wiring directly at/near the motor. This type of damage is not covered by warranty.
• To fit the motor correctly you may require the 5mm steel spacer behind the disc rotor (do not use the compressible plastic one supplied as this is for transportation only) and longer disc rotor bolts. If you are unsure at any stage, please kindly contact us and we will help.
• The kit is not waterproof and therefore should not be immersed in water. Water damage is not covered by warranty.
• Although this kit is renowned for being well designed and long-lasting, damages occurring from incorrect use of the kit is not covered by warranty. The kit is not suitable for doing jumps, wheelies, burnouts, impacts with kerbs, exceeding the recommended weight limit or downhill riding. The kit is most suited to riding on well paved surfaces and enjoying light gravel tracks.

NOTES

Torque arms/plates are not included. Please contact us should you require any more information on installation procedures.